| Hostname | IP Address | Status | Assigned To | Last Scan | Actions |
|---|---|---|---|---|---|
| MONTPOINTGTWYRTR | 10.10.10.1 | 2026-01-14 | |||
Finding DetailsEvaluate-STIG 1.2507.5 (Scan-CiscoXERouterNDM_Checks) found this to be OPEN on 10/23/2025 ResultHash: DD0C8EF05E5C236F6DE0AC78EFCA66F351187ECB ~~~~~ boot network not found ip boot server not found ip bootp server not found ip dns server not found ip identd not found ip finger not found ip http server not found ip rcmd rcp-enable not found ip rcmd rsh-enable not found service config not found service finger not found service tcp-small-servers not found service udp-small-servers not found service pad not found SERVICE CALL-HOME FOUND Comments |
|||||
Check Text
Verify that the router does not have any unnecessary or nonsecure ports, protocols, and services enabled. For example, the following commands should not be in the configuration: boot network ip boot server ip bootp server ip dns server ip identd ip finger ip http server ip rcmd rcp-enable ip rcmd rsh-enable service config service finger service tcp-small-servers service udp-small-servers service pad service call-home Note: Certain legacy devices may require 'service call-home' be enabled to support Smart Licensing as they do not support the newer smart transport configuration. Those devices do not incur a finding for having call-home enabled for Smart Licensing. If any unnecessary or nonsecure ports, protocols, or services are enabled, this is a finding.
Fix Text
Disable the following services if enabled as shown in the example below. R2(config)#no boot network R2(config)#no ip boot server R2(config)#no ip bootp server R2(config)#no ip dns server R2(config)#no ip identd R2(config)#no ip finger R2(config)#no ip http server R2(config)#no ip rcmd rcp-enable R2(config)#no ip rcmd rsh-enable R2(config)#no service config R2(config)#no service finger R2(config)#no service tcp-small-servers R2(config)#no service udp-small-servers R2(config)#no service pad R2(config)#no service call-home R2(config)#end
| Hostname | IP Address | Status | Assigned To | Last Scan | Actions |
|---|---|---|---|---|---|
| MONTPOINTGTWYRTR | 10.10.10.1 | 2026-01-14 | |||
Finding DetailsEvaluate-STIG 1.2507.5 (Scan-CiscoXERouterNDM_Checks) found this to be OPEN on 10/23/2025 ResultHash: EC2FCBD8253B86CFC2922A92FE8E178EA3988544 ~~~~~ IP HTTP Timeout Settings no ip http server no ip http secure-server http\https servers are disabled, http\https requirements are not applicable line con 0 privilege level 15 logging synchronous login authentication USER_AUTH stopbits 1 line con 0 exec-timeout is not configured. Default value of 10 is assumed Confirm value is correctly configured by checking against 'show running-config all' configuration file Line VTY Timeout Settings line vty 0 4 session-timeout 10 access-class vty_access in session-limit 3 logging synchronous transport preferred ssh transport input ssh transport output ssh ! exec-timeout is not configured. Default value of 10 is assumed Confirm value is correctly configured by checking against 'show running-config all' configuration file Comments |
|||||
Check Text
Review the Cisco router configuration to verify that all network connections associated with a device management have an idle timeout value set to five minutes or less as shown in the following example: ip http secure-server ip http timeout-policy idle 300 life nnnn requests nn … … … line con 0 exec-timeout 5 0 line vty 0 1 exec-timeout 5 0 If the Cisco router is not configured to terminate all network connections associated with a device management after five minutes of inactivity, this is a finding.
Fix Text
Set the idle timeout value to five minutes or less on all configured login classes as shown in the example below. R1(config)#line vty 0 1 R1(config-line)#exec-timeout 5 0 R1(config-line)#exit R1(config)#line con 0 R1(config-line)#exec-timeout 5 0 R1(config-line)#exit R2(config)#ip http timeout-policy idle 300 life nnnn requests nn
| Hostname | IP Address | Status | Assigned To | Last Scan | Actions |
|---|---|---|---|---|---|
| MONTPOINTGTWYRTR | 10.10.10.1 | 2026-01-14 | |||
Finding DetailsEvaluate-STIG 1.2507.5 (Scan-CiscoXERouterNDM_Checks) found this to be OPEN on 10/23/2025 ResultHash: FAA040DE8CA5849E5308201D0776B0A8AC84BA79 ~~~~~ SSH Server Algorithm is not configured per STIG check guidelines ip ssh source-interface BDI400 ip ssh logging events ip ssh version 2 ip ssh server algorithm mac hmac-sha1 ip ssh server algorithm encryption aes256-ctr aes192-ctr aes128-ctr Comments |
|||||
Check Text
Review the Cisco router configuration to verify that it is compliant with this requirement as shown in the example below. NOTE: Although allowed by SP800-131Ar2 for some applications, SHA-1 is considered a compromised hashing standard and is being phased out of use by industry and Government standards. Unless required for legacy use, DoD systems should not be configured to use SHA-1 for integrity of remote access sessions. SSH Example ip ssh version 2 ip ssh server algorithm mac hmac-sha2-256 If the Cisco router is not configured to use FIPS-validated HMAC to protect the integrity of remote maintenance sessions, this is a finding.
Fix Text
Configure SSH to use FIPS-validated HMAC for remote maintenance sessions as shown in the following example: SSH Example R1(config)#ip ssh version 2 R1(config)#ip ssh server algorithm mac hmac-sha2-256
| Hostname | IP Address | Status | Assigned To | Last Scan | Actions |
|---|---|---|---|---|---|
| MONTPOINTGTWYRTR | 10.10.10.1 | 2026-01-14 | |||
Finding DetailsEvaluate-STIG 1.2507.5 (Scan-CiscoXERouterNDM_Checks) found this to be OPEN on 10/23/2025 ResultHash: CA349E0F1566CFDFB09D8F996B3AD3B036574454 ~~~~~ The router is not configured to send log data to the syslog server, this is a finding. Comments |
|||||
Check Text
Verify that the router is configured to send logs to at least two syslog servers. The configuration should look similar to the example below: logging x.x.x.x logging x.x.x.x If the router is not configured to send log data to the syslog servers, this is a finding.
Fix Text
Configure the router to send log messages to the syslog servers as shown in the example below. R4(config)#logging host x.x.x.x R4(config)#logging host x.x.x.x
| Hostname | IP Address | Status | Assigned To | Last Scan | Actions |
|---|---|---|---|---|---|
| MONTPOINTGTWYRTR | 10.10.10.1 | 2026-01-14 | |||
Finding DetailsEvaluate-STIG 1.2507.5 (Scan-CiscoXERouterNDM_Checks) was unable to determine a Status but found the below configuration on 10/23/2025: ResultHash: F616F024AD309ED67328DF3127A0A41B41DA2441 ~~~~~ Check with vendor for support status of the device Device Info: Hostname : MONTPOINTGTWYRTR DomainName : MACAddress : DeviceInfo : {Cisco IOS Software [Gibraltar], ISR Software (X86_64_LINUX_IOSD-UNIVERSALK9-M), Version 16.12.4, RELEASE SOFTWARE (fc5)} CiscoOS : IOS-XE CiscoOSVer : 16.12.4 CiscoSoftware : ISR Software (X86_64_LINUX_IOSD-UNIVERSALK9-M) SerialNumber : FLM2122V0D9 Model : ISR4351/K9 DeviceType : Router Comments |
|||||
Check Text
Verify that the router is in compliance with this requirement by having the router administrator enter the following command: show version Verify that the release is still supported by Cisco. All releases supported by Cisco can be found on the following URL: www.cisco.com/c/en/us/support/ios-nx-os-software If the router is not running a supported release, this is a finding.
Fix Text
Upgrade the router to a supported release.
| Hostname | IP Address | Status | Assigned To | Last Scan | Actions |
|---|---|---|---|---|---|
| MONTPOINTGTWYRTR | 10.10.10.1 | 2026-01-14 | |||
Finding DetailsEvaluate-STIG 1.2507.5 (Scan-CiscoXERouterNDM_Checks) found this to be NOT A FINDING on 10/23/2025 ResultHash: 6FFE5E388F143FAEAC142114D4F65C55EDC01323 ~~~~~ service password-encryption Comments |
|||||
Check Text
Review the router configuration to determine if passwords are encrypted as shown in the example below. service password-encryption If the router is not configured to encrypt passwords, this is a finding.
Fix Text
Configure the router to encrypt all passwords. R4(config)#service password-encryption R4(config)#end
| Hostname | IP Address | Status | Assigned To | Last Scan | Actions |
|---|---|---|---|---|---|
| MONTPOINTGTWYRTR | 10.10.10.1 | 2026-01-14 | |||
Finding DetailsEvaluate-STIG 1.2507.5 (Scan-CiscoXERouterNDM_Checks) found this to be NOT A FINDING on 10/23/2025 ResultHash: 93C96089FB06A0232EAFE70A05C0C894B0598049 ~~~~~ ip ssh server algorithm encryption aes256-ctr aes192-ctr aes128-ctr Comments |
|||||
Check Text
Review the Cisco router configuration to verify that it is compliant with this requirement. SSH Example ip ssh version 2 ip ssh server algorithm encryption aes256-ctr aes192-ctr aes128-ctr If the router is not configured to implement cryptographic mechanisms to protect the confidentiality of remote maintenance sessions using a FIPS 140-2 approved algorithm, this is a finding.
Fix Text
Configure the Cisco router to implement cryptographic mechanisms to protect the confidentiality of remote maintenance sessions using a FIPS 140-2 approved algorithm as shown in the examples below. SSH Example R1(config)#ip ssh server algorithm encryption aes256-ctr aes192-ctr aes128-ctr
| Hostname | IP Address | Status | Assigned To | Last Scan | Actions |
|---|---|---|---|---|---|
| MONTPOINTGTWYRTR | 10.10.10.1 | 2026-01-14 | |||
Finding Detailsaaa new-model ! ! aaa group server radius AR21-Radius server name AR21-DC003 server name AR21-DC004 ip radius source-interface BDI400 load-balance method least-outstanding ! aaa group server tacacs+ ISE server-private 164.231.72.99 key 7 060B1C22424F1F0044 server-private 164.231.111.4 key 7 060B1C22424F1F0044 ip tacacs source-interface BDI400 ! aaa authentication login default group ISE group AR21-Radius local aaa authentication enable default group ISE group AR21-Radius enable aaa authorization config-commands aaa authorization exec default group ISE group AR21-Radius local if-authenticated aaa authorization network ISE group AR21-Radius local if-authenticated aaa accounting exec default start-stop group ISE group AR21-Radius ! aaa common-criteria policy PASSWORD_POLICY min-length 15 max-length 127 numeric-count 1 upper-case 1 lower-case 1 special-case 1 char-changes 8 ! ! ! ! ! ! aaa session-id common call-home ! If contact email address in call-home is configured as sch-smart-licensing@cisco.com ! the email address configured in Cisco Smart License Portal will be used as contact email address to send SCH notifications. contact-email-addr sch-smart-licensing@cisco.com profile "CiscoTAC-1" active destination transport-method http no destination transport-method email no ip source-route ! ! ! ! ! ! ! no ip domain lookup ip domain name MONTPOINTGTWRTR.navy.mil ! ! ! login block-for 900 attempts 3 within 120 login on-failure log login on-success log ipv6 hop-limit 32 Comments |
|||||
Check Text
Review the Cisco router configuration to verify the device is configured to use at least two authentication servers as primary source for authentication as shown in the following example: aaa new-model ! aaa authentication CONSOLE group radius local aaa authentication login LOGIN_AUTHENTICATION group radius local … … … ip http authentication aaa login-authentication LOGIN_AUTHENTICATION ip http secure-server … … … radius-server host x.x.x.x auth-port 1812 acct-port 1813 key xxxxxx radius-server host x.x.x.x auth-port 1812 acct-port 1813 key xxxxxx … … … line con 0 exec-timeout 5 0 login authentication CONSOLE line vty 0 1 exec-timeout 5 0 login authentication LOGIN_AUTHENTICATION If the Cisco router is not configured to use at least two authentication servers for the purpose of authenticating users prior to granting administrative access, this is a finding.
Fix Text
Step 1: Configure the Cisco router to use at least two authentication servers as shown in the following example: R4(config)#radius host 10.1.48.2 key xxxxxx R4(config)#radius host 10.1.48.3 key xxxxxx Step 2: Configure the authentication order to use the authentication servers as primary source for authentication as shown in the following example: R4(config)#aaa authentication CONSOLE group radius local R4(config)#aaa authentication login LOGIN_AUTHENTICATION group radius local Step 3: Configure all network connections associated with a device management to use the authentication servers for the purpose of login authentication. R4(config)#line vty 0 1 R4(config-line)#login authentication LOGIN_AUTHENTICATION R4(config-line)#exit R4(config)#line con 0 R4(config-line)#login authentication CONSOLE R4(config-line)#exit R4(config)#ip http authentication aaa login-authentication LOGIN_AUTHENTICATION
| Hostname | IP Address | Status | Assigned To | Last Scan | Actions |
|---|---|---|---|---|---|
| MONTPOINTGTWYRTR | 10.10.10.1 | 2026-01-14 | |||
Finding DetailsEvaluate-STIG 1.2507.5 (Scan-CiscoXERouterNDM_Checks) found this to be OPEN on 10/23/2025 ResultHash: B8F2A604E2162488415B37981572E5251E977016 ~~~~~ IP Http Server Settings: http\https servers are disabled, https requirements are not applicable no ip http server no ip http secure-server line vty 0 4 transport input ssh session-limit 3 Comments |
|||||
Check Text
Note: This requirement is not applicable to file transfer actions such as FTP, SCP, and SFTP. Review the router configuration to determine if concurrent management sessions are limited as shown in the example below: ip http secure-server ip http max-connections 2 … … … For platforms that support the session-limit command: line vty 0 4 session-limit 2 transport input ssh For those platforms that do not support the session-limit command, the sessions can also be limited by reducing the number of active vty lines as shown in the example below. line vty 0 1 transport input ssh line vty 2 4 transport input none If the router is not configured to limit the number of concurrent management sessions, this is a finding.
Fix Text
Configure the router to limit the number of concurrent management sessions to an organization-defined number as shown in the example below. R4(config)#ip http max-connections 2 R4(config)#line vty 0 1 R4(config-line)#transport input ssh R4(config-line)#exit R4(config)#line vty 2 4 R4(config-line)# transport input none R4(config-line)#end To configure session limiting, use the example below. R4(config)#line vty 0 4 R4(config-line)#session-limit 2 R4(config-line)#transport input ssh
| Hostname | IP Address | Status | Assigned To | Last Scan | Actions |
|---|---|---|---|---|---|
| MONTPOINTGTWYRTR | 10.10.10.1 | 2026-01-14 | |||
Finding DetailsEvaluate-STIG 1.2507.5 (Scan-CiscoXERouterNDM_Checks) found this to be OPEN on 10/23/2025 ResultHash: B1893061C5DDD560F8FECD36FB3416E58526B729 ~~~~~ Configured login banner DOES NOT match Standard Mandatory DoD Notice and Consent Banner as identified in STIG. Configured login banner: ##### Military Sealift Command (MSC) ##### ##### MSC Corporate Data Center(MCDC) ##### -------------------------------------------------------------------------------------- DOD WARNING BANNER -------------------------------------------------------------------------------------- You are accessing a U.S. Government (USG) Information System (IS) that is provided for USG-authorized use only. By using this IS (which includes any device attached to this IS), you consent to the following conditions: -The USG routinely intercepts and monitors communications on this IS for purposes including, but not limited to, penetration testing, COMSEC monitoring, network operations and defense, personnel misconduct (PM), law enforcement (LE), and counterintelligence (CI) investigations. -At any time, the USG may inspect and seize data stored on this IS. -Communications using, or data stored on, this IS are not private, are subject to routine monitoring, interception, and search, and may be disclosed or used for any USG authorized purpose. -This IS includes security measures (e.g., authentication and access controls) to protect USG interests--not for your personal benefit or privacy. -Notwithstanding the above, using this IS does not constitute consent to PM, LE or CI investigative searching or monitoring of the content of privileged communications, or work product, related to personal representation or services by attorneys, psychotherapists, or clergy, and their assistants. Such communications and work product are private and confidential. See User Agreement for details. ------------------------------------------------------------------------- DOD WARNING BANNER ------------------------------------------------------------------------- Comments |
|||||
Check Text
Review the Cisco router configuration to verify that it is compliant with this requirement as shown in the example below. banner login ^C You are accessing a U.S. Government (USG) Information System (IS) that is provided for USG-authorized use only. By using this IS (which includes any device attached to this IS), you consent to the following conditions: -The USG routinely intercepts and monitors communications on this IS for purposes including, but not limited to, penetration testing, COMSEC monitoring, network operations and defense, personnel misconduct (PM), law enforcement (LE), and counterintelligence (CI) investigations. -At any time, the USG may inspect and seize data stored on this IS. -Communications using, or data stored on, this IS are not private, are subject to routine monitoring, interception, and search, and may be disclosed or used for any USG-authorized purpose. -This IS includes security measures (e.g., authentication and access controls) to protect USG interests--not for your personal benefit or privacy. -Notwithstanding the above, using this IS does not constitute consent to PM, LE or CI investigative searching or monitoring of the content of privileged communications, or work product, related to personal representation or services by attorneys, psychotherapists, or clergy, and their assistants. Such communications and work product are private and confidential. See User Agreement for details. ^C If the Cisco router is not configured to display the Standard Mandatory DoD Notice and Consent Banner before granting access to the device, this is a finding.
Fix Text
Configure the Cisco router to display the Standard Mandatory DoD Notice and Consent Banner before granting access as shown in the following example: R1(config)#banner login # Enter TEXT message. End with the character '#'. You are accessing a U.S. Government (USG) Information System (IS) that is provided for USG-authorized use only. By using this IS (which includes any device attached to this IS), you consent to the following conditions: -The USG routinely intercepts and monitors communications on this IS for purposes including, but not limited to, penetration testing, COMSEC monitoring, network operations and defense, personnel misconduct (PM), law enforcement (LE), and counterintelligence (CI) investigations. -At any time, the USG may inspect and seize data stored on this IS. -Communications using, or data stored on, this IS are not private, are subject to routine monitoring, interception, and search, and may be disclosed or used for any USG-authorized purpose. -This IS includes security measures (e.g., authentication and access controls) to protect USG interests--not for your personal benefit or privacy. -Notwithstanding the above, using this IS does not constitute consent to PM, LE or CI investigative searching or monitoring of the content of privileged communications, or work product, related to personal representation or services by attorneys, psychotherapists, or clergy, and their assistants. Such communications and work product are private and confidential. See User Agreement for details. # R1(config)#end
| Hostname | IP Address | Status | Assigned To | Last Scan | Actions |
|---|---|---|---|---|---|
| MONTPOINTGTWYRTR | 10.10.10.1 | 2026-01-14 | |||
Finding DetailsEvaluate-STIG 1.2507.5 (Scan-CiscoXERouterNDM_Checks) found this to be OPEN on 10/23/2025 ResultHash: F317A8608580E65A7FD848FF078AE7B20D6F8440 ~~~~~ Accounts username emer-access privilege 0 secret 9 <pwd removed> Verify that a local account for last resort has been configured with a privilege level that will enable the administrator to troubleshoot connectivity to the authentication server. AAA Login Method: aaa authentication login default group ISE group AR21-Radius local Comments |
|||||
Check Text
Step 1: Review the Cisco router configuration to verify that a local account for last resort has been configured. username xxxxxxxxxxx privilege nn common-criteria-policy PASSWORD_POLICY password xxxxxxxxxx Note: The configured Common Criteria policy must be used when creating or changing the local account password as shown in the example above. Step 2: Verify that local is defined after radius or tacas+ in the authentication order as shown in the example below. aaa authentication login default group tacacs+ local If the Cisco router is not configured with only one local account to be used as the account of last resort in the event the authentication server is unavailable, this is a finding.
Fix Text
Step 1: Configure a local account as shown in the example below. R2(config)#username xxxxxxxxx privilege nn secret xxxxxxx Step 2: Configure the authentication order to use the local account if the authentication server is not reachable as shown in the following example: R2(config)#aaa authentication login default group tacacs+ local
| Hostname | IP Address | Status | Assigned To | Last Scan | Actions |
|---|---|---|---|---|---|
| MONTPOINTGTWYRTR | 10.10.10.1 | 2026-01-14 | |||
Finding DetailsEvaluate-STIG 1.2507.5 (Scan-CiscoXERouterNDM_Checks) found this to be OPEN on 10/23/2025 ResultHash: 5F8368BFC68F3878D80F5B9647E5D732EB331313 ~~~~~ 'logging buffered' is not configured Comments |
|||||
Check Text
Verify that the Cisco router is configured with a logging buffer size. The configuration should look like the example below: logging buffered xxxxxxxx informational If a logging buffer size is not configured, this is a finding. If the Cisco router is not configured to allocate audit record storage capacity in accordance with organization-defined audit record storage requirements, this is a finding.
Fix Text
Configure the buffer size for logging as shown in the example below. R2(config)#logging buffered xxxxxxxx informational
| Hostname | IP Address | Status | Assigned To | Last Scan | Actions |
|---|---|---|---|---|---|
| MONTPOINTGTWYRTR | 10.10.10.1 | 2026-01-14 | |||
Finding DetailsEvaluate-STIG 1.2507.5 (Scan-CiscoXERouterNDM_Checks) found this to be OPEN on 10/23/2025 ResultHash: 887A831BD26D733D8E7BF0EFA917C4970FFE1B26 ~~~~~ Cisco router is not configured to conduct backups of the configuration when changes occur Comments |
|||||
Check Text
Review the Cisco router configuration to verify that it is compliant with this requirement. The example configuration below will send the configuration to a SCP server when a configuration change occurs. event manager applet BACKUP_CONFIG event syslog pattern "%SYS-5-CONFIG_I" action 1 info type routername action 2 cli command "enable" action 3 cli command "copy run scp" pattern "remote host" action 4 cli command "x.x.x.x" pattern "filename" action 5 cli command "$_info_routername-config" action 6 syslog priority informational msg "Configuration backup was executed" If the Cisco router is not configured to conduct backups of the configuration when changes occur, this is a finding.
Fix Text
Configure the Cisco router to send the configuration to a SCP server when a configuration change occurs as shown in the example below. R4(config)#event manager applet BACKUP_CONFIG R4(config-applet)#event syslog pattern "%SYS-5-CONFIG_I" R4(config-applet)#action 1 cli command "enable" R4(config-applet)#action 2 info type routername R4(config-applet)#action 3 cli command "copy run scp" pattern "remote host" R4(config-applet)#action 4 cli command "x.x.x.x" pattern "filename" R4(config-applet)#action 5 cli command "$_info_routername-config" R4(config-applet)#action 6 syslog priority informational msg "Configuration backup was executed" R4(config-applet)#end
| Hostname | IP Address | Status | Assigned To | Last Scan | Actions |
|---|---|---|---|---|---|
| MONTPOINTGTWYRTR | 10.10.10.1 | 2026-01-14 | |||
Finding DetailsEvaluate-STIG 1.2507.5 (Scan-CiscoXERouterNDM_Checks) found this to be OPEN on 10/23/2025 ResultHash: 173712CE30761257E28758267267A6B72D8F12F1 ~~~~~ crypto pki trustpoint TP-self-signed-1964743403 is not configured for url enrollment crypto pki trustpoint TP-self-signed-1964743403 enrollment selfsigned crypto pki trustpoint SLA-TrustPoint is not configured for url enrollment crypto pki trustpoint SLA-TrustPoint enrollment pkcs12 crypto pki trustpoint TP-self-signed-941045115 is not configured for url enrollment crypto pki trustpoint TP-self-signed-941045115 enrollment selfsigned Comments |
|||||
Check Text
Review the router configuration to determine if a CA trust point has been configured. The CA trust point will contain the URL of the CA in which the router has enrolled with. Verify this is a DOD or DOD-approved CA. This will ensure the router has enrolled and received a certificate from a trusted CA. The CA trust point configuration would look similar to the example below. crypto pki trustpoint CA_X enrollment url http://trustpoint1.example.com Note: A remote end-point's certificate will always be validated by the router by verifying the signature of the CA on the certificate using the CA's public key, which is contained in the router's certificate it received at enrollment. Note: This requirement is not applicable if the router does not have any public key certificates. If the Cisco router is not configured to obtain its public key certificates from an appropriate certificate policy through an approved service provider, this is a finding.
Fix Text
Configure the router to obtain its public key certificates from an appropriate certificate policy through an approved service provider as shown in the example below. R2(config)# crypto pki trustpoint CA_X R2(ca-trustpoint)#enrollment url http://trustpoint1.example.com
| Hostname | IP Address | Status | Assigned To | Last Scan | Actions |
|---|---|---|---|---|---|
| MONTPOINTGTWYRTR | 10.10.10.1 | 2026-01-14 | |||
Finding DetailsEvaluate-STIG 1.2507.5 (Scan-CiscoXERouterNDM_Checks) found this to be NOT A FINDING on 10/23/2025 ResultHash: A678C60E1EAF17D7C51ED8282DC985211C33F443 ~~~~~ Archive log config logging enable logging size 1000 notify syslog contenttype plaintext hidekeys Comments |
|||||
Check Text
Review the router configuration to determine if it automatically audits account creation. The configuration should look similar to the example below: archive log config logging enable Note: Configuration changes can be viewed using the show archive log config all command. If account creation is not automatically audited, this is a finding.
Fix Text
Configure the router to log account creation using the following commands: R4(config)#archive R4(config-archive)#log config R4(config-archive-log-cfg)#logging enable R4(config-archive-log-cfg)#logging size 1000 R4(config-archive-log-cfg)#notify syslog contenttype plaintext R4(config-archive-log-cfg)#hidekeys R4(config-archive-log-cfg)#end
| Hostname | IP Address | Status | Assigned To | Last Scan | Actions |
|---|---|---|---|---|---|
| MONTPOINTGTWYRTR | 10.10.10.1 | 2026-01-14 | |||
Finding DetailsEvaluate-STIG 1.2507.5 (Scan-CiscoXERouterNDM_Checks) found this to be NOT A FINDING on 10/23/2025 ResultHash: A678C60E1EAF17D7C51ED8282DC985211C33F443 ~~~~~ Archive log config logging enable logging size 1000 notify syslog contenttype plaintext hidekeys Comments |
|||||
Check Text
Review the router configuration to determine if it automatically audits account modification. The configuration should look similar to the example below: archive log config logging enable Note: Configuration changes can be viewed using the show archive log config all command. If account modification is not automatically audited, this is a finding.
Fix Text
Configure the router to log account modification using the following commands: R4(config)#archive R4(config-archive)#log config R4(config-archive-log-cfg)#logging enable R4(config-archive-log-cfg)#logging size 1000 R4(config-archive-log-cfg)#notify syslog contenttype plaintext R4(config-archive-log-cfg)#hidekeys R4(config-archive-log-cfg)#end
| Hostname | IP Address | Status | Assigned To | Last Scan | Actions |
|---|---|---|---|---|---|
| MONTPOINTGTWYRTR | 10.10.10.1 | 2026-01-14 | |||
Finding DetailsEvaluate-STIG 1.2507.5 (Scan-CiscoXERouterNDM_Checks) found this to be NOT A FINDING on 10/23/2025 ResultHash: A678C60E1EAF17D7C51ED8282DC985211C33F443 ~~~~~ Archive log config logging enable logging size 1000 notify syslog contenttype plaintext hidekeys Comments |
|||||
Check Text
Review the router configuration to determine if it automatically audits account disabling. The configuration should look similar to the example below: archive log config logging enable Note: Configuration changes can be viewed using the show archive log config all command. If account disabling is not automatically audited, this is a finding.
Fix Text
Configure the router to log account disabling using the following commands: R4(config)#archive R4(config-archive)#log config R4(config-archive-log-cfg)#logging enable R4(config-archive-log-cfg)#logging size 1000 R4(config-archive-log-cfg)#notify syslog contenttype plaintext R4(config-archive-log-cfg)#hidekeys R4(config-archive-log-cfg)#end
| Hostname | IP Address | Status | Assigned To | Last Scan | Actions |
|---|---|---|---|---|---|
| MONTPOINTGTWYRTR | 10.10.10.1 | 2026-01-14 | |||
Finding DetailsEvaluate-STIG 1.2507.5 (Scan-CiscoXERouterNDM_Checks) found this to be NOT A FINDING on 10/23/2025 ResultHash: A678C60E1EAF17D7C51ED8282DC985211C33F443 ~~~~~ Archive log config logging enable logging size 1000 notify syslog contenttype plaintext hidekeys Comments |
|||||
Check Text
Review the router configuration to determine if it automatically audits account removal. The configuration should look similar to the example below: archive log config logging enable Note: Configuration changes can be viewed using the show archive log config all command. If account removal is not automatically audited, this is a finding.
Fix Text
Configure the router to log account removal using the following commands: R4(config)#archive R4(config-archive)#log config R4(config-archive-log-cfg)#logging enable R4(config-archive-log-cfg)#logging size 1000 R4(config-archive-log-cfg)#notify syslog contenttype plaintext R4(config-archive-log-cfg)#hidekeys R4(config-archive-log-cfg)#end
| Hostname | IP Address | Status | Assigned To | Last Scan | Actions |
|---|---|---|---|---|---|
| MONTPOINTGTWYRTR | 10.10.10.1 | 2026-01-14 | |||
Finding DetailsEvaluate-STIG 1.2507.5 (Scan-CiscoXERouterNDM_Checks) was unable to determine a Status but found the below configuration on 10/23/2025: ResultHash: 7C34C4946A66BAD21BCD23A9B909B63F3502B98E ~~~~~ line vty 0 4 session-timeout 10 access-class vty_access in session-limit 3 logging synchronous transport preferred ssh transport input ssh transport output ssh ! ip access-list extended vty_access 10 remark Allow access from other ships, NOCs or Afloat Support 10 permit tcp 164.231.0.0 0.0.255.255 any eq 22 log 20 deny ip any any log ! ! ! ! ! ! ! Comments |
|||||
Check Text
Review the Cisco router configuration to verify that it is compliant with this requirement. Step 1: Verify that the line vty has an ACL inbound applied as shown in the example below. line vty 0 1 access-class MANAGEMENT_NET in transport input ssh Step 2: Verify that the ACL permits only hosts from the management network to access the router. ip access-list extended MANAGEMENT_NET permit ip x.x.x.0 0.0.0.255 any deny ip any any log-input If the Cisco router is not configured to enforce approved authorizations for controlling the flow of management information within the device based on control policies, this is a finding.
Fix Text
Configure the Cisco router to restrict management access to specific IP addresses via SSH as shown in the example below. SW2(config)#ip access-list standard MANAGEMENT_NET SW2(config-std-nacl)#permit x.x.x.0 0.0.0.255 SW2(config-std-nacl)#exit SW2(config)#line vty 0 1 SW2(config-line)#transport input ssh SW2(config-line)#access-class MANAGEMENT_NET in SW2(config-line)#end
| Hostname | IP Address | Status | Assigned To | Last Scan | Actions |
|---|---|---|---|---|---|
| MONTPOINTGTWYRTR | 10.10.10.1 | 2026-01-14 | |||
Finding DetailsEvaluate-STIG 1.2507.5 (Scan-CiscoXERouterNDM_Checks) found this to be NOT A FINDING on 10/23/2025 ResultHash: ABBAB8CC78DE7347B6202BF8F03B33B9A6291A0E ~~~~~ login block-for 900 attempts 3 within 120 Comments |
|||||
Check Text
Review the Cisco router configuration to verify that it enforces the limit of three consecutive invalid logon attempts as shown in the example below. login block-for 900 attempts 3 within 120 Note: The configuration example above will block any login attempt for 15 minutes after three consecutive invalid logon attempts within a two-minute period. If the Cisco router is not configured to enforce the limit of three consecutive invalid logon attempts, this is a finding.
Fix Text
Configure the Cisco router to enforce the limit of three consecutive invalid logon attempts as shown in the example below. R2(config)#login block-for 900 attempts 3 within 120
| Hostname | IP Address | Status | Assigned To | Last Scan | Actions |
|---|---|---|---|---|---|
| MONTPOINTGTWYRTR | 10.10.10.1 | 2026-01-14 | |||
Finding DetailsEvaluate-STIG 1.2507.5 (Scan-CiscoXERouterNDM_Checks) found this to be NOT A FINDING on 10/23/2025 ResultHash: 8FFBED927D401C4C59BC347DFFD3868F3306C61D ~~~~~ hostname MONTPOINTGTWYRTR logging userinfo archive log config logging enable logging size 1000 notify syslog contenttype plaintext hidekeys Comments |
|||||
Check Text
Review the Cisco router configuration to verify that it is compliant with this requirement as shown in the example below. hostname R1 ! logging userinfo ! … … … archive log config logging enable ! Note: The logging userinfo global configuration command will generate a log when a user increases his or her privilege level. If logging of administrator activity is not configured, this is a finding.
Fix Text
Configure the router to log administrator activity as shown in the example below. R1(config)#logging userinfo R1(config)#archive R1(config-archive)#log config R1(config-archive-log-cfg)#logging enable R1(config-archive-log-cfg)#logging size 1000 R1(config-archive-log-cfg)#notify syslog contenttype plaintext R1(config-archive-log-cfg)#hidekeys R1(config-archive-log-cfg)#end
| Hostname | IP Address | Status | Assigned To | Last Scan | Actions |
|---|---|---|---|---|---|
| MONTPOINTGTWYRTR | 10.10.10.1 | 2026-01-14 | |||
Finding DetailsEvaluate-STIG 1.2507.5 (Scan-CiscoXERouterNDM_Checks) found this to be NOT A FINDING on 10/23/2025 ResultHash: DE0D02323230142232357AF55AE5B85E1C6CF819 ~~~~~ service timestamps log datetime msec localtime show-timezone year Comments |
|||||
Check Text
Verify that the router is configured to include the date and time on all log records as shown in the configuration example below. service timestamps log datetime localtime If time stamps are not configured, this is a finding.
Fix Text
Configure the router to include the date and time on all log records as shown in the example below. R1(config)#service timestamps log datetime localtime
| Hostname | IP Address | Status | Assigned To | Last Scan | Actions |
|---|---|---|---|---|---|
| MONTPOINTGTWYRTR | 10.10.10.1 | 2026-01-14 | |||
Finding DetailsEvaluate-STIG 1.2507.5 (Scan-CiscoXERouterNDM_Checks) found this to be NOT A FINDING on 10/23/2025 ResultHash: 949FD62A829175C2132E70DF0486F90EB24C9A8A ~~~~~ All 'deny' statements are configured to log. Comments |
|||||
Check Text
Review the deny statements in all interface ACLs to determine if the log-input parameter has been configured as shown in the example below. Note: log-input can only apply to interface bound ACLs. ip access-list extended BLOCK_INBOUND deny icmp any any log-input If the router is not configured with the log-input parameter after any deny statements to note where packets have been dropped via an ACL, this is a finding.
Fix Text
Configure the log-input parameter after any deny statements to provide the location as to where packets have been dropped via an ACL. R1(config)#ip access-list extended BLOCK_INBOUND R1(config-ext-nacl)#deny icmp any any log-input
| Hostname | IP Address | Status | Assigned To | Last Scan | Actions |
|---|---|---|---|---|---|
| MONTPOINTGTWYRTR | 10.10.10.1 | 2026-01-14 | |||
Finding DetailsEvaluate-STIG 1.2507.5 (Scan-CiscoXERouterNDM_Checks) found this to be NOT A FINDING on 10/23/2025 ResultHash: A678C60E1EAF17D7C51ED8282DC985211C33F443 ~~~~~ Archive log config logging enable logging size 1000 notify syslog contenttype plaintext hidekeys Comments |
|||||
Check Text
Review the Cisco router configuration to verify that it is compliant with this requirement. The configuration example below will log all configuration changes. archive log config logging enable Note: Configuration changes can be viewed using the show archive log config all command. If the Cisco router is not configured to generate audit records of configuration changes, this is a finding.
Fix Text
Configure the Cisco router to log all configuration changes as shown in the example below. R4(config)#archive R4(config-archive)#log config R4(config-archive-log-cfg)#logging enable R4(config-archive-log-cfg)#logging size 1000 R4(config-archive-log-cfg)#notify syslog contenttype plaintext R4(config-archive-log-cfg)#hidekeys R4(config-archive-log-cfg)#end
| Hostname | IP Address | Status | Assigned To | Last Scan | Actions |
|---|---|---|---|---|---|
| MONTPOINTGTWYRTR | 10.10.10.1 | 2026-01-14 | |||
Finding DetailsEvaluate-STIG 1.2507.5 (Scan-CiscoXERouterNDM_Checks) found this to be NOT APPLICABLE on 10/23/2025 ResultHash: BE9D336E6083AAD077B0C802971ECCA37B641B51 ~~~~~ Logging persistent not found, this requirement is not applicable Comments |
|||||
Check Text
Review the Cisco router configuration to verify that it is compliant with this requirement. Step 1: If persistent logging is enabled as shown in the example below, go to step 2. Otherwise, this requirement is not applicable. logging persistent url disk0:/logfile size 134217728 filesize 16384 Step 2: Verify that the router is not configured with a privilege level other than "15" to allow access to the file system as shown in the example below. file privilege 10 Note: The default privilege level required for access to the file system is "15"; hence, the command file privilege "15" will not be shown in the configuration. If the router is configured with a privilege level other than "15" to allow access to the file system, this is a finding.
Fix Text
If persistent logging is enabled, configure the router to only allow administrators with privilege level "15" access to the file system as shown in the example below. R4(config)#file privilege 15
| Hostname | IP Address | Status | Assigned To | Last Scan | Actions |
|---|---|---|---|---|---|
| MONTPOINTGTWYRTR | 10.10.10.1 | 2026-01-14 | |||
Finding DetailsEvaluate-STIG 1.2507.5 (Scan-CiscoXERouterNDM_Checks) found this to be NOT APPLICABLE on 10/23/2025 ResultHash: BE9D336E6083AAD077B0C802971ECCA37B641B51 ~~~~~ Logging persistent not found, this requirement is not applicable Comments |
|||||
Check Text
Review the Cisco router configuration to verify that it is compliant with this requirement. Step 1: If persistent logging is enabled as shown in the example below, go to step 2. Otherwise, this requirement is not applicable. logging persistent url disk0:/logfile size 134217728 filesize 16384 Step 2: Verify that the router is not configured with a privilege level other than "15" to allow access to the file system as shown in the example below. file privilege 10 Note: The default privilege level required for access to the file system is "15"; hence, the command file privilege "15" will not be shown in the configuration. If the router is configured with a privilege level other than "15" to allow access to the file system, this is a finding.
Fix Text
If persistent logging is enabled, configure the router to only allow administrators with privilege level "15" access to the file system as shown in the example below. R4(config)#file privilege 15
| Hostname | IP Address | Status | Assigned To | Last Scan | Actions |
|---|---|---|---|---|---|
| MONTPOINTGTWYRTR | 10.10.10.1 | 2026-01-14 | |||
Finding DetailsEvaluate-STIG 1.2507.5 (Scan-CiscoXERouterNDM_Checks) was unable to determine a Status but found the below configuration on 10/23/2025: ResultHash: 27E2CCFBEAF21F0CF88252AA3BD21746F050EEB7 ~~~~~ File privilege configuration was not found File privilege 15 configuration is assumed Please verify settings on router Comments |
|||||
Check Text
Verify that the router is not configured with a privilege level other than "15" to allow access to the file system as shown in the example below. file privilege 10 Note: The default privilege level required for access to the file system is "15"; hence, the command file privilege "15" will not be shown in the configuration. If the router is configured with a privilege level other than "15" to allow access to the file system, this is a finding.
Fix Text
Configure the router to only allow administrators with privilege level "15" access to the file system as shown in the example below. R4(config)#file privilege 15
| Hostname | IP Address | Status | Assigned To | Last Scan | Actions |
|---|---|---|---|---|---|
| MONTPOINTGTWYRTR | 10.10.10.1 | 2026-01-14 | |||
Finding DetailsEvaluate-STIG 1.2507.5 (Scan-CiscoXERouterNDM_Checks) found this to be NOT A FINDING on 10/23/2025 ResultHash: C4104C43FF3450C0073B61738529B67004F83A5B ~~~~~ aaa common-criteria policy PASSWORD_POLICY min-length 15 Comments |
|||||
Check Text
Review the Cisco router configuration to verify that it is compliant with this requirement as shown in the example below. aaa new-model ! ! aaa common-criteria policy PASSWORD_POLICY min-length 15 If the Cisco router is not configured to enforce a minimum 15-character password length, this is a finding.
Fix Text
Configure the Cisco router to enforce a minimum 15-character password length as shown in the example below. R1(config)#aaa common-criteria policy PASSWORD_POLICY R1(config-cc-policy)#min-length 15 R1(config-cc-policy)#exit
| Hostname | IP Address | Status | Assigned To | Last Scan | Actions |
|---|---|---|---|---|---|
| MONTPOINTGTWYRTR | 10.10.10.1 | 2026-01-14 | |||
Finding DetailsEvaluate-STIG 1.2507.5 (Scan-CiscoXERouterNDM_Checks) found this to be NOT A FINDING on 10/23/2025 ResultHash: 6553FABD4B56D1A387B5DB3F6CF16C838667FAFF ~~~~~ aaa common-criteria policy PASSWORD_POLICY upper-case 1 Comments |
|||||
Check Text
Review the Cisco router configuration to verify that it is compliant with this requirement as shown in the example below. aaa new-model ! ! aaa common-criteria policy PASSWORD_POLICY upper-case 1 If the Cisco router is not configured to enforce password complexity by requiring that at least one uppercase character be used, this is a finding.
Fix Text
Configure the Cisco router to enforce password complexity by requiring that at least one uppercase character be used as shown in the example below. R1(config)#aaa common-criteria policy PASSWORD_POLICY R1(config-cc-policy)#upper-case 1 R1(config-cc-policy)#exit
| Hostname | IP Address | Status | Assigned To | Last Scan | Actions |
|---|---|---|---|---|---|
| MONTPOINTGTWYRTR | 10.10.10.1 | 2026-01-14 | |||
Finding DetailsEvaluate-STIG 1.2507.5 (Scan-CiscoXERouterNDM_Checks) found this to be NOT A FINDING on 10/23/2025 ResultHash: 6C8C9A04EE0049FF30F16D96F6497AEF4B48F61F ~~~~~ aaa common-criteria policy PASSWORD_POLICY lower-case 1 Comments |
|||||
Check Text
Review the Cisco router configuration to verify that it is compliant with this requirement as shown in the example below. aaa new-model ! ! aaa common-criteria policy PASSWORD_POLICY lower-case 1 If the Cisco router is not configured to enforce password complexity by requiring that at least one lowercase character be used, this is a finding.
Fix Text
Configure the Cisco router to enforce password complexity by requiring that at least one lowercase character be used as shown in the example below. R1(config)#aaa common-criteria policy PASSWORD_POLICY R1(config-cc-policy)#lower-case 1 R1(config-cc-policy)#exit
| Hostname | IP Address | Status | Assigned To | Last Scan | Actions |
|---|---|---|---|---|---|
| MONTPOINTGTWYRTR | 10.10.10.1 | 2026-01-14 | |||
Finding DetailsEvaluate-STIG 1.2507.5 (Scan-CiscoXERouterNDM_Checks) found this to be NOT A FINDING on 10/23/2025 ResultHash: B33379AD6F2ED0966DBD92772AE64D65D2E60892 ~~~~~ aaa common-criteria policy PASSWORD_POLICY numeric-count 1 Comments |
|||||
Check Text
Review the Cisco router configuration to verify that it is compliant with this requirement as shown in the example below. aaa new-model ! ! aaa common-criteria policy PASSWORD_POLICY numeric-count 1 If the Cisco router is not configured to enforce password complexity by requiring that at least one numeric character be used, this is a finding.
Fix Text
Configure the Cisco router to enforce password complexity by requiring that at least one numeric character be used as shown in the example below. R1(config)#aaa common-criteria policy PASSWORD_POLICY R1(config-cc-policy)#numeric-count 1 R1(config-cc-policy)#exit
| Hostname | IP Address | Status | Assigned To | Last Scan | Actions |
|---|---|---|---|---|---|
| MONTPOINTGTWYRTR | 10.10.10.1 | 2026-01-14 | |||
Finding DetailsEvaluate-STIG 1.2507.5 (Scan-CiscoXERouterNDM_Checks) found this to be NOT A FINDING on 10/23/2025 ResultHash: 3716573D24AFF025B7A4466C19199D89373DCDC6 ~~~~~ aaa common-criteria policy PASSWORD_POLICY special-case 1 Comments |
|||||
Check Text
Review the Cisco router configuration to verify that it is compliant with this requirement as shown in the example below. aaa new-model ! ! aaa common-criteria policy PASSWORD_POLICY special-case 1 If the Cisco router is not configured to enforce password complexity by requiring that at least one special character be used, this is a finding.
Fix Text
Configure the Cisco router to enforce password complexity by requiring that at least one special character be used as shown in the example below. R1(config)#aaa common-criteria policy PASSWORD_POLICY R1(config-cc-policy)#special-case 1 R1(config-cc-policy)#exit
| Hostname | IP Address | Status | Assigned To | Last Scan | Actions |
|---|---|---|---|---|---|
| MONTPOINTGTWYRTR | 10.10.10.1 | 2026-01-14 | |||
Finding DetailsEvaluate-STIG 1.2507.5 (Scan-CiscoXERouterNDM_Checks) found this to be NOT A FINDING on 10/23/2025 ResultHash: B24372278E11DB93CB56DA5D58F2C691579D30F4 ~~~~~ aaa common-criteria policy PASSWORD_POLICY char-changes 8 Comments |
|||||
Check Text
Review the Cisco router configuration to verify that it is compliant with this requirement as shown in the example below. aaa new-model ! ! aaa common-criteria policy PASSWORD_POLICY char-changes 8 If the Cisco router is not configured to require that when a password is changed, the characters are changed in at least eight of the positions within the password, this is a finding.
Fix Text
Configure the Cisco router to enforce password complexity by requiring that when a password is changed, the characters are changed in at least eight of the positions within the password as shown in the example below. R1(config)#aaa common-criteria policy PASSWORD_POLICY R1(config-cc-policy)#char-changes 8 R1(config-cc-policy)#exit
| Hostname | IP Address | Status | Assigned To | Last Scan | Actions |
|---|---|---|---|---|---|
| MONTPOINTGTWYRTR | 10.10.10.1 | 2026-01-14 | |||
Finding DetailsEvaluate-STIG 1.2507.5 (Scan-CiscoXERouterNDM_Checks) found this to be NOT A FINDING on 10/23/2025 ResultHash: A678C60E1EAF17D7C51ED8282DC985211C33F443 ~~~~~ Archive log config logging enable logging size 1000 notify syslog contenttype plaintext hidekeys Comments |
|||||
Check Text
Review the router configuration to determine if it automatically audits account enabling. The configuration should look similar to the example below: archive log config logging enable Note: Configuration changes can be viewed using the show archive log config all command. If account enabling is not automatically audited, this is a finding.
Fix Text
Configure the router to log account enabling using the following commands: R4(config)#archive R4(config-archive)#log config R4(config-archive-log-cfg)#logging enable R4(config-archive-log-cfg)#logging size 1000 R4(config-archive-log-cfg)#notify syslog contenttype plaintext R4(config-archive-log-cfg)#hidekeys R4(config-archive-log-cfg)#end
| Hostname | IP Address | Status | Assigned To | Last Scan | Actions |
|---|---|---|---|---|---|
| MONTPOINTGTWYRTR | 10.10.10.1 | 2026-01-14 | |||
Finding DetailsEvaluate-STIG 1.2507.5 (Scan-CiscoXERouterNDM_Checks) found this to be NOT A FINDING on 10/23/2025 ResultHash: AC8D3D82BA9C34A72D08AFC9E465F551B1580A74 ~~~~~ Trap logging: level informational, 815 message lines logged Comments |
|||||
Check Text
Review the Cisco router configuration to verify that it is compliant with this requirement as shown in the example below. logging trap critical Note: The parameter "critical" can replaced with a lesser severity level (i.e. error, warning, notice, informational). Informational is the default severity level; hence, if the severity level is configured to informational, the logging trap command will not be shown in the configuration. If the Cisco router is not configured to generate an alert for all audit failure events, this is a finding.
Fix Text
Configure the Cisco router to send critical to emergency log messages to the syslog server as shown in the example below. R4(config)#logging trap critical Note: The parameter "critical" can replaced with a lesser severity level (i.e., error, warning, notice, informational).
| Hostname | IP Address | Status | Assigned To | Last Scan | Actions |
|---|---|---|---|---|---|
| MONTPOINTGTWYRTR | 10.10.10.1 | 2026-01-14 | |||
Finding DetailsEvaluate-STIG 1.2507.5 (Scan-CiscoXERouterNDM_Checks) found this to be NOT A FINDING on 10/23/2025 ResultHash: 5CB0787E1E482D4AD90CB4D79FFA8280B5A635AC ~~~~~ ntp server 164.231.98.1 key 20 ntp server 164.231.69.13 key 80 prefer Comments |
|||||
Check Text
Review the Cisco router configuration to verify that it is compliant with this requirement as shown in the configuration example below. ntp server x.x.x.x ntp server y.y.y.y If the Cisco router is not configured to synchronize its clock with redundant authoritative time sources, this is a finding.
Fix Text
Configure the Cisco router to synchronize its clock with redundant authoritative time sources as shown in the example below. R2(config)#ntp server x.x.x.x R2(config)#ntp server y.y.y.y
| Hostname | IP Address | Status | Assigned To | Last Scan | Actions |
|---|---|---|---|---|---|
| MONTPOINTGTWYRTR | 10.10.10.1 | 2026-01-14 | |||
Finding DetailsEvaluate-STIG 1.2507.5 (Scan-CiscoXERouterNDM_Checks) was unable to determine a Status but found the below configuration on 10/23/2025: ResultHash: 1DB45E772E2D5C909D9677E4B1376C0A674A7D4B ~~~~~ Requires information not provided by show tech or show running configuration file Comments |
|||||
Check Text
Review the Cisco router configuration to verify that it is compliant with this requirement as shown in the example below. snmp-server group V3GROUP v3 auth read V3READ write V3WRITE snmp-server host x.x.x.x version 3 auth V3USER Authentication used by the SNMP users can be viewed via the show snmp user command as shown in the example below: R4#show snmp user User name: V3USER Engine ID: 800000090300C2042B540000 storage-type: nonvolatile active Authentication Protocol: SHA Privacy Protocol: None Group-name: V3GROUP If the Cisco router is not configured to authenticate SNMP messages using a FIPS-validated HMAC, this is a finding.
Fix Text
Configure the Cisco router to authenticate SNMP messages as shown in the example below: R4(config)#snmp-server group V3GROUP v3 auth read V3READ write V3WRITE R4(config)#snmp-server user V3USER V3GROUP v3 auth sha xxxxxxx R4(config)#snmp-server host x.x.x.x version 3 auth V3USER
| Hostname | IP Address | Status | Assigned To | Last Scan | Actions |
|---|---|---|---|---|---|
| MONTPOINTGTWYRTR | 10.10.10.1 | 2026-01-14 | |||
Finding DetailsEvaluate-STIG 1.2507.5 (Scan-CiscoXERouterNDM_Checks) was unable to determine a Status but found the below configuration on 10/23/2025: ResultHash: 1DB45E772E2D5C909D9677E4B1376C0A674A7D4B ~~~~~ Requires information not provided by show tech or show running configuration file Comments |
|||||
Check Text
Review the Cisco router configuration to verify that it is compliant with this requirement as shown in the example below. snmp-server group V3GROUP v3 priv read V3READ write V3WRITE snmp-server view V3READ iso included snmp-server view V3WRITE iso included snmp-server host x.x.x.x version 3 auth V3USER Encryption used by the SNMP users can be viewed via the show snmp user command as shown in the example below. R4#show snmp user User name: V3USER Engine ID: 800000090300C2042B540000 storage-type: nonvolatile active Authentication Protocol: SHA Privacy Protocol: AES256 Group-name: V3GROUP If the Cisco router is not configured to encrypt SNMP messages using a FIPS 140-2 approved algorithm, this is a finding.
Fix Text
Configure the Cisco router to encrypt SNMP messages using a FIPS 140-2 approved algorithm as shown in the example below. R4(config)#snmp-server group V3GROUP v3 priv read V3READ write V3WRITE R4(config)#snmp-server user V3USER V3GROUP v3 auth sha xxxxxx priv aes 256 xxxxxx
| Hostname | IP Address | Status | Assigned To | Last Scan | Actions |
|---|---|---|---|---|---|
| MONTPOINTGTWYRTR | 10.10.10.1 | 2026-01-14 | |||
Finding DetailsEvaluate-STIG 1.2507.5 (Scan-CiscoXERouterNDM_Checks) found this to be NOT A FINDING on 10/23/2025 ResultHash: 746684BF0C80384E74956B54D242941B88392F07 ~~~~~ ntp allow mode control 0 ntp authentication-key 80 md5 0021450F24771D4F387C521D5936042A32 7 ntp authentication-key 20 md5 10401D090E120B051814212E3D 7 ntp trusted-key 20 ntp trusted-key 80 ntp source BDI400 ntp server 164.231.98.1 key 20 ntp server 164.231.69.13 key 80 prefer Comments |
|||||
Check Text
Review the Cisco router configuration to verify that it is compliant with this requirement as shown in the configuration example below. ntp authentication-key 1 hmac-sha2-256 xxxxxx ntp authenticate ntp trusted-key 1 ntp server x.x.x.x key 1 ntp server y.y.y.y key 1 If the Cisco router is not configured to authenticate NTP sources using authentication that is cryptographically based, this is a finding.
Fix Text
Configure the Cisco router to authenticate NTP sources using authentication that is cryptographically based as shown in the example below. R2(config)#ntp authenticate R2(config)#ntp authentication-key 1 hmac-sha2-256 xxxxxxx R2(config)#ntp trusted-key 1 R2(config)#ntp server x.x.x.x key 1 R2(config)#ntp server y.y.y.y key 1
| Hostname | IP Address | Status | Assigned To | Last Scan | Actions |
|---|---|---|---|---|---|
| MONTPOINTGTWYRTR | 10.10.10.1 | 2026-01-14 | |||
Finding DetailsEvaluate-STIG 1.2507.5 (Scan-CiscoXERouterNDM_Checks) found this to be NOT A FINDING on 10/23/2025 ResultHash: A678C60E1EAF17D7C51ED8282DC985211C33F443 ~~~~~ Archive log config logging enable logging size 1000 notify syslog contenttype plaintext hidekeys Comments |
|||||
Check Text
Review the Cisco router configuration to verify that it is compliant with this requirement as shown in the example below. archive log config logging enable If the Cisco router is not configured to generate log records when administrator privileges are deleted, this is a finding.
Fix Text
Configure the Cisco router to generate log records when administrator privileges are deleted as shown in the example below. R4(config)#archive R4(config-archive)#log config R4(config-archive-log-cfg)#logging enable R4(config-archive-log-cfg)#logging size 1000 R4(config-archive-log-cfg)#notify syslog contenttype plaintext R4(config-archive-log-cfg)#hidekeys R4(config-archive-log-cfg)#end
| Hostname | IP Address | Status | Assigned To | Last Scan | Actions |
|---|---|---|---|---|---|
| MONTPOINTGTWYRTR | 10.10.10.1 | 2026-01-14 | |||
Finding DetailsEvaluate-STIG 1.2507.5 (Scan-CiscoXERouterNDM_Checks) found this to be NOT A FINDING on 10/23/2025 ResultHash: A19CCFDDF163501A636769305EE4AE7BC1A36158 ~~~~~ login on-failure log login on-success log Comments |
|||||
Check Text
Review the Cisco router configuration to verify that it is compliant with this requirement as shown in the examples below. login on-failure log login on-success log If the Cisco router is not configured to generate audit records when successful/unsuccessful logon attempts occur, this is a finding.
Fix Text
Configure the Cisco router to generate audit records when successful/unsuccessful logon attempts occur as shown in the example below. R5(config)#login on-failure log R5(config)#login on-success log
| Hostname | IP Address | Status | Assigned To | Last Scan | Actions |
|---|---|---|---|---|---|
| MONTPOINTGTWYRTR | 10.10.10.1 | 2026-01-14 | |||
Finding DetailsEvaluate-STIG 1.2507.5 (Scan-CiscoXERouterNDM_Checks) found this to be NOT A FINDING on 10/23/2025 ResultHash: A678C60E1EAF17D7C51ED8282DC985211C33F443 ~~~~~ Archive log config logging enable logging size 1000 notify syslog contenttype plaintext hidekeys Comments |
|||||
Check Text
Review the Cisco router configuration to verify that it is compliant with this requirement as shown in the example configurations below. archive log config logging enable If the Cisco router is not configured to generate log records for privileged activities, this is a finding.
Fix Text
Configure the Cisco router to generate log records for privileged activities as shown in the example below. R4(config)#archive R4(config-archive)#log config R4(config-archive-log-cfg)#logging enable R4(config-archive-log-cfg)#logging size 1000 R4(config-archive-log-cfg)#notify syslog contenttype plaintext R4(config-archive-log-cfg)#hidekeys R4(config-archive-log-cfg)#end